Congrats to our New President Anguss!!
Remember to like us on Facebook!! - https://www.facebook.com/skylinesdownunder

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - cwint

Pages: [1] 2
1
Australia / Any One Misplaced Their R32 Gtr????
« on: August 07, 2011, 05:48:54 PM »
please delete

2
Australia / Any One Misplaced Their R32 Gtr????
« on: August 07, 2011, 11:58:41 AM »
um theres a black gtr abandonded at the bottom of my hill in shand st stafford brisbane, probly stolen so if its yours? Better pick it up before some mongrel does.

3
Forced Induction / r34 gtr turbo identification
« on: October 10, 2005, 11:15:23 PM »
does anyone know what the identifying features of an r34 gtr turbo looks like,  what numbers they have printed on them?

4
General Performance / what are these off?
« on: August 31, 2005, 10:57:16 PM »
does anyone know where these rear hubs are off? they are full aluminium as apposed to the cast steel ones in my gtst  they would be good for unsprung weight but i dont know what they are off as they were headed for the scrap before i saved them.

5
Naturally Aspirated / help r32 gts25 manual diff ratios
« on: June 07, 2005, 11:12:00 PM »
ive just searched through old post trying to find this out but theres nothing. i need a higher ratio diff as my engine doesnt need to be revving so high and i have been offered one of these but dont know if its any better than what i have.any one know for sure?

i think i currently am running a 4:36

6
General Performance / tilton vtripple plate clutch
« on: May 25, 2005, 08:59:44 PM »
has anyone used these in their cars?
does anyone know where to get new centre spline plates to suit gtst?

7
Maintenance & Car Care / help igniter box
« on: May 06, 2005, 08:38:50 PM »
does anyone know how to replace the igniter box with something reliable? i think another one has died and im sick of trying to find them. or does any one know how to check that they work? im running a link ecu so i dont have the diagnostics anymore.:headbutt: :headbutt: :headbutt: :headbutt:

8
SDU Central / dyno day
« on: April 27, 2005, 05:50:17 PM »
is anyone going to the dyno day in palmy on 14th may at fortec performance?
$50 2wd $80 4wd here

9
Forced Induction / gtr cooler fitting
« on: March 10, 2005, 11:11:12 PM »
anyone got any photos of the fitting of a gtr cooler on a gtst
or any tips for doing it.

10
General Performance / r32 4dr/2dr exhaust the same?
« on: March 02, 2005, 10:52:11 PM »
anyone tried putting a 4dr exhaust on a 2dr? do they fit the same?

11
Auckland and North / anyone know James Yong Chen Hon ?
« on: December 19, 2004, 10:06:28 AM »
i bought some wheel adaptors from him and havent seen them yet any one know where he is
helensville auckland.

12
General Performance / clutch splines sizes?
« on: December 06, 2004, 10:13:57 PM »
ive got an r32 rp71c gearbox from turbo/na skyline and i want a heavy clutch/flywheel combo and ive seen a gtr flywheel/clutch for sale but dont know if it will fit my gearbox input shaft,can any one help?:king:

13
General Performance / rb30 spigot bush
« on: November 23, 2004, 05:46:20 PM »
has anyone had any probs with an rb30 spigot bush pb22?
i bought one from b&t and tried to put it in but it didnt look like it was going to go so i measured it and it measured 20.7 o/d 16 i/d but the hole in my crank is 20 and the input shaft is 16 so even if i bash it in id still have to bore out the inside, so i took it back and they said they had sold 3-4 in the last 6 months and havent had any back.
does anyone know whats going on or what bush to use?:splat:

14
Forced Induction / rb30det volumetric efficiency
« on: October 15, 2004, 11:29:40 PM »
does anyone know roughly what the volumetric efficiency of an rb30det would be?:king:

15
General Performance / rb30 engine parts
« on: September 30, 2004, 09:48:20 PM »
im in the process of building my rb30 and am wondering what people have used for theirs,
i got prices for parts today:
chrome-moly rings $223.30+gst
mains $56.57+
b/ends $47.80+
rb25det head gasket $179.20+
rb30e head gasket 59.16+
these prices are pretty good but i need to know what people have used, is it worth using the det head gasket or is the 30e h/g fine?
are the standy rings fine or are C/M rings needed?
they couldnt get half grove b/e bearings so are standy ones good enough?
also where do you get nismo heavy duty bearings from and what are they worth roughly?
any help would be much appreciated.
 (but please if you havent got something nice to say.....)

Pages: [1] 2