Congrats to our New President Anguss!!
Remember to like us on Facebook!! - https://www.facebook.com/skylinesdownunder

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Drift-monkey

Pages: [1] 2 3 ... 5
1
General Performance / Re: Clutch not engaging
« on: November 07, 2016, 01:36:40 PM »
What would be a giveaway that's it's the wrong clutch? 9 bolt 240mm as opposed to the 250mm flywheel that's on there (if that makes any difference?). Clutch was brought in with a bunch of parts from the states that a friend of mine ordered.. will give him a buzz and see what's up.

2
General Performance / Re: Clutch not engaging
« on: November 04, 2016, 11:42:26 AM »
Fork is moving, gravity bled clutch till fluid came from slave and then bled from master cyl, good pedal pressure,  pulled box back out and spline changes resistance with each gear so gearbox is good (?). Stumped.

3
General Performance / Clutch not engaging
« on: October 27, 2016, 10:37:31 AM »
Having problems with my gts4 with gtr box, clutch isn't engaging? Had the car idling and it was selecting gears without clutch in, doesn't move with clutch in/out at all. New clutch, new spigot bush, new release bearing, clutch aligned. Could the gearbox be suspect?

4
Why are you removing that part? It's what keeps water off the door card when it's raining, otherwise, sharp blades to scrape 80% off, then soak in prepsol/degreaser/thinners and wipe it away.... lots.... lol not a fun job aye

5
Picture Post / Re: ECR32 4dr Skyline Build (Now HNR32)
« on: September 25, 2016, 05:27:09 PM »
Still not running hahaha, very close now though, clutch issue to sort out, oil pump gasket still leaking ever so slightly. Am just going to leave it for a bit more and then pay a shop to finish it off and then will get it tuned and run in..




6
Picture Post / Re: ECR32 4dr Skyline Build (Now HNR32)
« on: July 18, 2016, 07:51:52 PM »
Yeah, replaced front seal because of the heat given to crank timing pulley when heating it up to get it off, replaced the rear because it was the "ah might as well" situation. Got pretty much everything I need to get off, all the sump bolts etc just need to drop sump and take last two bolts for oil pump off, throw new gasket in and it'll be reassembly time. Bit of a hiccup but still just glad that's been the only problem. Got a new gearbox mount to chuck in also.
Gets too dark these days not enough play time under the car

7
Picture Post / Re: ECR32 4dr Skyline Build (Now HNR32)
« on: July 15, 2016, 01:56:47 PM »
haha, thats a bastard of a place to get a leak :( what sealant did you use?

It was in a tube in the garage, indicated that it was for automotive use but the driveway says it's obviously not oil proof. Got a proper gasket from Nissan on the way. Hard lesson learned haha, couldn't think of a worse place 

8
Picture Post / Re: ECR32 4dr Skyline Build (Now HNR32)
« on: July 14, 2016, 10:58:31 AM »
nice work. you seam surprised it runs. must be a good feeling to have it running.

Definitely surprised it's running haha, I would have thought it'd have grenaded itself on first startup. I'm usually one to forget things especially because this is the first time ive ever done any of this before, in saying that, it pissed oil all over driveway from the oil pump gasket (wrong sealant used) which is a pain in the ass but it started first pop and sounded healthy so I'm not complaining. Will sort that out and then finish up the rest of it.

9
Picture Post / Re: ECR32 4dr Skyline Build (Now HNR32)
« on: July 13, 2016, 10:32:51 PM »
It actually runs...  8) 8) 8) 8) 8) 8). Pics and vids to come.

10
Picture Post / Re: ECR32 4dr Skyline Build (Now HNR32)
« on: July 02, 2016, 06:24:29 PM »






Can count the things that need doing on one hand now. Just slowly working through it all.

11
Picture Post / Re: ECR32 4dr Skyline Build (Now HNR32)
« on: June 30, 2016, 04:51:18 PM »
Cheers Looney_Head.  Definitely getting there slowly but surely. Subframe and mounts are all in, started doing everything up now, fuel lines etc. Rained so will continue tomorrow, hopefully have it running on the weekend :D

12
Picture Post / Re: ECR32 4dr Skyline Build (Now HNR32)
« on: June 30, 2016, 04:49:59 PM »

13
Picture Post / Re: ECR32 4dr Skyline Build (Now HNR32)
« on: June 29, 2016, 01:27:51 PM »
Too rainy. Engine is sitting on subframe with a jack under the subframe, just gotta jack it up into place and lower car down onto subframe then plug everything in and she'll be ready for first start up. Still nervous being my first build. Hoping it doesn't pack a sad first start.



Will be wicked to drive the car again but in manual this time. Can't wait till Friday then it'll be finishing it off and run it in time.

14
Picture Post / Re: ECR32 4dr Skyline Build (Now HNR32)
« on: May 31, 2016, 02:18:23 AM »




New clutch on, timing and cambelt strapped up. Nearly there.

15
Picture Post / Re: ECR32 4dr Skyline Build (Now HNR32)
« on: May 26, 2016, 09:03:00 PM »
lol at the RFB spec cleanliness while building this engine.

Pages: [1] 2 3 ... 5