Congrats to our New President Anguss!!
Remember to like us on Facebook!! - https://www.facebook.com/skylinesdownunder

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Looney_Head

Pages: 1 [2] 3 4 ... 172
16
Introductions / New Member Welcomes / Re: My RB30DET money pit
« on: August 10, 2017, 01:35:29 PM »
thats not too bad a list, could you not remove the rear seats and have it certified as a two seater?

that drop will be a challenge, what brand are your coil overs? i don't know if mine have 40mm of drop :( maybe disconnect the swaybar and take it for a recheck.

17
Off-Topic / Re: Helllloooooooooooo
« on: July 14, 2017, 08:30:44 AM »
getting there, only spending a day a week on the wiring is taking ages. currently have the wipers, windows, switch panel and engine left. then all done

18
Introductions / New Member Welcomes / Re: My RB30DET money pit
« on: July 14, 2017, 08:29:25 AM »
i should really check how far my sump hangs..

good luck with the cert.

19
Off-Topic / Re: Helllloooooooooooo
« on: July 10, 2017, 07:50:59 AM »
Yo man, i am still kicking round and still building my R32, I have updated my build thread a few times recently. once its going i will be getting it out to tracks for fun.

20
Picture Post / Re: Looney_Head build
« on: June 15, 2017, 08:42:20 AM »
some more progress, Fuse/relay/ecu panel is complete and all heat shrinked.



and in the car:


and new toy turned up, currently having a mate 3D print a mounting system for it:


next is start the under dash wiring for things like lights, indicators, horn etc. fun times..

21
Introductions / New Member Welcomes / Re: My RB30DET money pit
« on: June 13, 2017, 11:28:10 AM »
does your sump sit very low? did you lower your engine on the mounts or do you just have a massive sump?

22
Picture Post / Re: Looney_Head build
« on: May 29, 2017, 07:59:51 AM »
fingers crossed. the months just keep flying by at the moment :(

23
Picture Post / Re: Looney_Head build
« on: May 24, 2017, 08:11:51 AM »
Man its been a while since i updated this the car went to my mates place getting the fabrication done and came back and now the long task of getting it finished has started.

first job hang the exhaust:


next up was mounting the intercooler and piping:





intake piping:


and dump pipe/wastegate pipe:





also picked up a couple of driveshaft loops for a R32 sedan:


a Fenix radiator was purchased:


power steering was sorted:


Coolant line was sorted:


LS coil on plug setup has been mounted:


Exhaust has been wrapped and installed for the final time:


hot side of the engine is fully assembled, oil feeds and returns, dump pipe the lot:


Switch panel in progress, and new 3 bar map sensor:



and Adrian (Pizzaboy) has made excellent work on the wiring, still dash and engine loom left, but getting there slowly:



oh and have ordered a Haltech Street dash so that will look nice in the car when it turns up.

24
have you checked for any vacuum leaks? does the car have a standard bov?

25
SDU Central / Re: Y44 v8 engine
« on: March 08, 2017, 08:00:28 AM »
very unique, how much effort was involved to make it fit in there and mate it to a trans?

26
Introductions / New Member Welcomes / Re: My RB30DET money pit
« on: March 07, 2017, 07:59:37 AM »
i like those wheels and tyres, whats the combo? and yeah it looks tough.

any videos of KiwiNats?

27
Picture Post / Re: Nish's new ride
« on: March 06, 2017, 07:58:21 AM »
lol, only 7 years over due in your updates :P

28
Introductions / New Member Welcomes / Re: My RB30DET money pit
« on: February 09, 2017, 08:21:33 AM »
how do you find the 366 on spool and transient throttle?

what rims and tyres are you running?

29
Introductions / New Member Welcomes / Re: My RB30DET money pit
« on: February 08, 2017, 07:48:25 AM »
very nice power. that torque is impressive. 700ish Nm, solid.

was that on pump gas?

30
Introductions / New Member Welcomes / Re: My RB30DET money pit
« on: January 29, 2017, 10:19:32 PM »
awesome work, what pump controllers are those? i am going to use a solid state relay and a pwm output on the ecu for mine.

Rims look good.

Pages: 1 [2] 3 4 ... 172